Reference: RBD-3101
Banner

The fingerprint algorithm extracts features from the acquired fingerprint image and represents the fingerprint information. The storage, comparison, and search of fingerprints are all done by operating fingerprint features. RoboticsBD
Fingerprint processing includes two processes: fingerprint registration process and fingerprint matching process (in which fingerprint matching is divided into fingerprint comparison (1:1) and fingerprint search (1:N) two ways). RoboticsBD
When the fingerprint is registered, two fingerprints are entered for each fingerprint, and the input image is processed twice. The synthesis module is stored in the module.
When the fingerprint is matched, the fingerprint sensor is used to input the fingerprint image to be verified and processed, and then it is compared with the fingerprint module in the module (if it is matched with a module specified in the module, it is called fingerprint comparison mode, ie, 1:1 mode. If matching with multiple modules is called fingerprint search, ie 1:N mode, the module gives the matching result (pass or fail). Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Low power consumption, low cost, small size, excellent performance, Professional optical technology, precise module manufacturing technics. Good image processing capabilities can successfully capture an image up to resolution 500 dpi Finger detection function. RoboticsBD

RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RED ---Arduino 3.3V
Yellow---Arduino D2
White----Arduino D3
Black----Arduino GND
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Resolution | 500dpi |
| Supply current | <60mA |
| Supply voltage | 3.3V |
| Fingerprint image entry time | <1.0 seconds |
| Peak current | <60mA |
| Window area(mm) | 15.3×18.2 |
| Communication Interface | USB/UART |
| Length (mm) | 46 |
| Width (mm) | 21 |
| Height (mm) | 24 |
| Weight (gm) | 20 |
| Shipment Weight | 0.03 kg |
| Shipment Dimensions | 5 × 3 × 2 cm |
Please allow 5% measuring deviation due to manual measurement.
1 x Fingerprint Scanner Sensor JM-101
1 x Connecting Cable(6-pin).
Specific References
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: RBD-3101
Reference: RBD-1919
Reference: RBD-3771
Reference: RBD-1740
Reference: RBD-2343
Reference: RBD-1194
Reference: RBD-1858
Reference: RBD-0673
Reference: RBD-3094
Brand: DFRobot
Reference: RBD-2229
Reference: RBD-1914
Reference: RBD-2093
Reference: RBD-3142
Reference: RBD-3584
Brand: DFRobot
Reference: RBD-2507
Reference: RBD-0391
Reference: RBD-0094
Reference: RBD-0133
Reference: RBD-0020
Reference: RBD-0768
Reference: RBD-0755
Reference: RBD-1349
Reference: RBD-0694
Reference: RBD-0094
Reference: RBD-0442
Reference: RBD-1680
Reference: RBD-0264
Brand: SparkFun Electronics
Reference: RBD-1043
check_circle
check_circle