• Banner

Active filters
  • Availability: In stock
  • Categories: 3D Printed
  • Categories: Battery & Charger
  • Categories: Communication Module
  • Categories: Motor Driver

Reference: RBD-0573

DC 5V Stepper Motor with ULN2003 Driver Board 28BYJ-48

(0)
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
BDT 199.00
BDT 199.00 tax incl.
BDT 199.00 tax excl.
BDT 199.00 tax excl.
BDT 199.00 tax incl.
BDT 199.00 tax incl.
BDT 0.00 Tax
BDT 199.00 tax excl.
BDT 199.00 tax excl.
BDT 0.00 Tax
BDT 199.00 tax incl.
More
In-Stock
In stock: 104

Reference: RBD-0284

5.8GHz Circular Polarized Mushroom Antenna RP-SMA Set Tx/Rx for FPV Multicopter

(0)
Gain: 2.0dBi-2.5dBi Antenna connector: RP-SMA Male Connector Standing wave ratio(SWR): <1.5 Weight: TxA10.3g, RxA 11.5g TxA is a circular-polarized Omni antenna with three lobes RxA is a circular-polarized Omni antenna with four lobes
BDT 880.00
BDT 880.00 tax incl.
BDT 880.00 tax excl.
BDT 880.00 tax excl.
BDT 880.00 tax incl.
BDT 880.00 tax incl.
BDT 0.00 Tax
BDT 880.00 tax excl.
BDT 880.00 tax excl.
BDT 0.00 Tax
BDT 880.00 tax incl.
More
In-Stock
In stock: 6

Reference: RBD-0262

Jumper Wire housing 6 Pin

(0)
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
BDT 20.00
BDT 20.00 tax incl.
BDT 20.00 tax excl.
BDT 20.00 tax excl.
BDT 20.00 tax incl.
BDT 20.00 tax incl.
BDT 0.00 Tax
BDT 20.00 tax excl.
BDT 20.00 tax excl.
BDT 0.00 Tax
BDT 20.00 tax incl.
More
In-Stock
In stock: 5

Reference: RBD-0662

EasyDriver Shield Stepper Motor Driver V44 A3967 For Arduino

(0)
Power supply: 7V to 30V. The higher the voltage, the higher the torque at high speeds. Adjustable current control from 150mA/phase to 750mA/phase. Logic voltage: 5V or 3.3V. A3967 microstepping driver. RoboticsBD
BDT 350.00
BDT 350.00 tax incl.
BDT 350.00 tax excl.
BDT 350.00 tax excl.
BDT 350.00 tax incl.
BDT 350.00 tax incl.
BDT 0.00 Tax
BDT 350.00 tax excl.
BDT 350.00 tax excl.
BDT 0.00 Tax
BDT 350.00 tax incl.
More
In-Stock
In stock: 11

Reference: RBD-0345

ESP-01 ESP8266 Serial WIFI Wireless Transceiver Module

(0)
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
BDT 230.00
BDT 230.00 tax incl.
BDT 230.00 tax excl.
BDT 230.00 tax excl.
BDT 230.00 tax incl.
BDT 230.00 tax incl.
BDT 0.00 Tax
BDT 230.00 tax excl.
BDT 230.00 tax excl.
BDT 0.00 Tax
BDT 230.00 tax incl.
More
In-Stock
In stock: 388

Reference: RBD-0263

Jumper Wire housing 7 Pin

(0)
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
BDT 25.00
BDT 25.00 tax incl.
BDT 25.00 tax excl.
BDT 25.00 tax excl.
BDT 25.00 tax incl.
BDT 25.00 tax incl.
BDT 0.00 Tax
BDT 25.00 tax excl.
BDT 25.00 tax excl.
BDT 0.00 Tax
BDT 25.00 tax incl.
More
In-Stock
In stock: 5

Reference: RBD-0212

B3 Pro Lipo Balance Charger

(0)
Input: 110v or 240v A/C (50/60Hz) Cell Count: 2~3s Battery Type: LiPoly Output Current: 3 x 800mA
BDT 599.00
BDT 599.00 tax incl.
BDT 599.00 tax excl.
BDT 599.00 tax excl.
BDT 599.00 tax incl.
BDT 599.00 tax incl.
BDT 0.00 Tax
BDT 599.00 tax excl.
BDT 599.00 tax excl.
BDT 0.00 Tax
BDT 599.00 tax incl.
More
In-Stock
In stock: 20

Reference: RBD-0927

Lipo Battery 1000mAh 11.1V 3S

(0)
Weight: 85 gm. Voltage : 11.1 V. Dimensions : 17 x 34 x 72(mm ). Max Continuous Discharge : 25 C(25 A). Balance Plug : JST-XH. Discharge Plug : XT-60.
BDT 1,450.00
BDT 1,450.00 tax incl.
BDT 1,450.00 tax excl.
BDT 1,450.00 tax excl.
BDT 1,450.00 tax incl.
BDT 1,450.00 tax incl.
BDT 0.00 Tax
BDT 1,450.00 tax excl.
BDT 1,450.00 tax excl.
BDT 0.00 Tax
BDT 1,450.00 tax incl.
More
In-Stock
In stock: 30

Reference: RBD-0684

Motor Driver - Dual TB6612FNG (1A)

(0)
CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
BDT 420.00
BDT 420.00 tax incl.
BDT 420.00 tax excl.
BDT 420.00 tax excl.
BDT 420.00 tax incl.
BDT 420.00 tax incl.
BDT 0.00 Tax
BDT 420.00 tax excl.
BDT 420.00 tax excl.
BDT 0.00 Tax
BDT 420.00 tax incl.
More
In-Stock
In stock: 16

Reference: RBD-0269

Jumper Wire housing 8 Pin

(0)
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
BDT 25.00
BDT 25.00 tax incl.
BDT 25.00 tax excl.
BDT 25.00 tax excl.
BDT 25.00 tax incl.
BDT 25.00 tax incl.
BDT 0.00 Tax
BDT 25.00 tax excl.
BDT 25.00 tax excl.
BDT 0.00 Tax
BDT 25.00 tax incl.
More
In-Stock
In stock: 8

Reference: RBD-0103

M177 NRF24L01 2.4GHz Antenna Wireless Transceiver Module

(0)
This is M177 NRF24L01 2.4GHz Antenna Wireless Transceiver Module. The nRF24L01 is a highly integrated, ultra-low power (ULP) 2Mbps RF transceiver IC for the 2.4GHz ISM (Industrial, Scientific, and Medical) band. With peak RX/TX currents lower than 14mA, a sub μA power down mode, advanced power management, and a 1.9 to 3.6V supply range, the nRF24L01...
BDT 199.00
BDT 199.00 tax incl.
BDT 199.00 tax excl.
BDT 199.00 tax excl.
BDT 199.00 tax incl.
BDT 199.00 tax incl.
BDT 0.00 Tax
BDT 199.00 tax excl.
BDT 199.00 tax excl.
BDT 0.00 Tax
BDT 199.00 tax incl.
More
In-Stock
In stock: 102

Reference: RBD-0928

Lipo Battery 1200mAh 11.1V 3S

(0)
Voltage : 11.1V Constant Discharge : 30C(10.5A) Max discharge : 25C (10 sec) Dimensions : 74 x 34 x 22 (LxWxH)(mm ) Weight : 87 gm Charge Rate : 1-3C Recommended, 5C Max
BDT 1,590.00
BDT 1,590.00 tax incl.
BDT 1,590.00 tax excl.
BDT 1,590.00 tax excl.
BDT 1,590.00 tax incl.
BDT 1,590.00 tax incl.
BDT 0.00 Tax
BDT 1,590.00 tax excl.
BDT 1,590.00 tax excl.
BDT 0.00 Tax
BDT 1,590.00 tax incl.
More
In-Stock
In stock: 10

Reference: RBD-0703

SSC-32 32Ch Servo Controller Lynxmotion Compatible

(0)
Controls up to 32 servo motors Comes preassembled USB interface (cable included), Xbee socket, and TTL serial Bidirectional communication with Query commands Large capacitors to prevent brownouts
BDT 3,400.00
BDT 3,400.00 tax incl.
BDT 3,400.00 tax excl.
BDT 3,400.00 tax excl.
BDT 3,400.00 tax incl.
BDT 3,400.00 tax incl.
BDT 0.00 Tax
BDT 3,400.00 tax excl.
BDT 3,400.00 tax excl.
BDT 0.00 Tax
BDT 3,400.00 tax incl.
More
In-Stock
In stock: 7

Reference: RBD-0566

RS485 USB-485 Converter Adapter Support Win7 XP Vista Linux Mac OS

(0)
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
BDT 1,000.00
BDT 1,000.00 tax incl.
BDT 1,000.00 tax excl.
BDT 1,000.00 tax excl.
BDT 1,000.00 tax incl.
BDT 1,000.00 tax incl.
BDT 0.00 Tax
BDT 1,000.00 tax excl.
BDT 1,000.00 tax excl.
BDT 0.00 Tax
BDT 1,000.00 tax incl.
More
In-Stock
In stock: 43

Reference: RBD-1681

Jumper Wire housing 4Pin

(0)
3D printed Dupont connector for Jumper cable 4pin
BDT 60.00
BDT 60.00 tax incl.
BDT 60.00 tax excl.
BDT 60.00 tax excl.
BDT 60.00 tax incl.
BDT 60.00 tax incl.
BDT 0.00 Tax
BDT 60.00 tax excl.
BDT 60.00 tax excl.
BDT 0.00 Tax
BDT 60.00 tax incl.
More
In-Stock
In stock: 17

Reference: RBD-0929

Lipo Battery 1500mAh 11.1V 3S

(0)
Weight : 97 gm Voltage: 11.1V Capacity: 1500mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
BDT 1,750.00
BDT 1,750.00 tax incl.
BDT 1,750.00 tax excl.
BDT 1,750.00 tax excl.
BDT 1,750.00 tax incl.
BDT 1,750.00 tax incl.
BDT 0.00 Tax
BDT 1,750.00 tax excl.
BDT 1,750.00 tax excl.
BDT 0.00 Tax
BDT 1,750.00 tax incl.
More
In-Stock
In stock: 26

Reference: RBD-0742

Motor Driver 43A BTS7960

(0)
Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
BDT 670.00
BDT 670.00 tax incl.
BDT 670.00 tax excl.
BDT 670.00 tax excl.
BDT 670.00 tax incl.
BDT 670.00 tax incl.
BDT 0.00 Tax
BDT 670.00 tax excl.
BDT 670.00 tax excl.
BDT 0.00 Tax
BDT 670.00 tax incl.
More
In-Stock
In stock: 44

Reference: RBD-0440

HC-12 433Mhz Wireless Serial Transceiver Module - 1 Kilometer

(0)
433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes. RoboticsBD
BDT 590.00
BDT 590.00 tax incl.
BDT 590.00 tax excl.
BDT 590.00 tax excl.
BDT 590.00 tax incl.
BDT 590.00 tax incl.
BDT 0.00 Tax
BDT 590.00 tax excl.
BDT 590.00 tax excl.
BDT 0.00 Tax
BDT 590.00 tax incl.
More
In-Stock
In stock: 24

Reference: RBD-2182

3D Printer Nozzle M7 Thread Brass 1.75mm

(0)
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Screw outer diameter: M7 If you are not sure which Nozzle size to choose, Please check our guide in the documentation tab below. 
BDT 190.00
BDT 190.00 tax incl.
BDT 190.00 tax excl.
BDT 190.00 tax excl.
BDT 190.00 tax incl.
BDT 190.00 tax incl.
BDT 0.00 Tax
BDT 190.00 tax excl.
BDT 190.00 tax excl.
BDT 0.00 Tax
BDT 190.00 tax incl.
More
In-Stock
In stock: 28

Reference: RBD-1606

L297 Stepper Motor Controller IC

(0)
Supply Voltage Range: 4.75V to 7V Driver Case Style: DIP No. of Pins: 20 Operating Temperature Range: -40°C to +150°C
BDT 96.00
BDT 96.00 tax incl.
BDT 96.00 tax excl.
BDT 96.00 tax excl.
BDT 96.00 tax incl.
BDT 96.00 tax incl.
BDT 0.00 Tax
BDT 96.00 tax excl.
BDT 96.00 tax excl.
BDT 0.00 Tax
BDT 96.00 tax incl.
More
In-Stock
In stock: 46

Reference: RBD-0930

Lipo Battery 2200mAh 11.1V 3S

(0)
Weight : 182 gm Voltage: 11.1V Capacity: 2200mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
BDT 2,500.00
BDT 2,500.00 tax incl.
BDT 2,500.00 tax excl.
BDT 2,500.00 tax excl.
BDT 2,500.00 tax incl.
BDT 2,500.00 tax incl.
BDT 0.00 Tax
BDT 2,500.00 tax excl.
BDT 2,500.00 tax excl.
BDT 0.00 Tax
BDT 2,500.00 tax incl.
More
In-Stock
In stock: 9

Reference: RBD-2534

4 DOF High Precision 3D-Printed Stepper Motor Robotic Arm

(0)
3D-printed robotic arm with 4 stepper motors and 1 servo motor for precise control Robot arm size: approximately 25 x 13 x 29 cm Features claws for easy gripping Includes all necessary 3D-printed parts and motors The color and claw mechanism of the Robotic arm  may vary as our stock rotates. Current stock comes as assembled. 
BDT 13,499.00
BDT 13,499.00 tax incl.
BDT 13,499.00 tax excl.
BDT 13,499.00 tax excl.
BDT 13,499.00 tax incl.
BDT 13,499.00 tax incl.
BDT 0.00 Tax
BDT 13,499.00 tax excl.
BDT 13,499.00 tax excl.
BDT 0.00 Tax
BDT 13,499.00 tax incl.
More
Last items in stock
In stock: 1

Reference: RBD-1678

Big Easy Driver - Stepper Motor Driver

(0)
2A phase 3D Printer Big Easy Driver board V1.2 A4988 stepper motor driver board Module
BDT 699.00
BDT 699.00 tax incl.
BDT 699.00 tax excl.
BDT 699.00 tax excl.
BDT 699.00 tax incl.
BDT 699.00 tax incl.
BDT 0.00 Tax
BDT 699.00 tax excl.
BDT 699.00 tax excl.
BDT 0.00 Tax
BDT 699.00 tax incl.
More
In-Stock
In stock: 28

Reference: RBD-0931

Lipo Battery 3300mAh 11.1V 3S

(0)
Weight : 190 gm Voltage: 11.1V Capacity: 3300mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
BDT 3,490.00
BDT 3,490.00 tax incl.
BDT 3,490.00 tax excl.
BDT 3,490.00 tax excl.
BDT 3,490.00 tax incl.
BDT 3,490.00 tax incl.
BDT 0.00 Tax
BDT 3,490.00 tax excl.
BDT 3,490.00 tax excl.
BDT 0.00 Tax
BDT 3,490.00 tax incl.
More
In-Stock
In stock: 22

Reference: RBD-0443

GPRS GSM SIM900 Arduino Shield

(0)
Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
BDT 2,400.00
BDT 2,400.00 tax incl.
BDT 2,400.00 tax excl.
BDT 2,400.00 tax excl.
BDT 2,400.00 tax incl.
BDT 2,400.00 tax incl.
BDT 0.00 Tax
BDT 2,400.00 tax excl.
BDT 2,400.00 tax excl.
BDT 0.00 Tax
BDT 2,400.00 tax incl.
More
In-Stock
In stock: 22

Reference: RBD-2695

US-015 Ultrasonic Module Housing

(0)
Custom 3D-printed enclosure designed specifically for the US-015 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. Features two screw holes for convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates. 
BDT 80.00
BDT 80.00 tax incl.
BDT 80.00 tax excl.
BDT 80.00 tax excl.
BDT 80.00 tax incl.
BDT 80.00 tax incl.
BDT 0.00 Tax
BDT 80.00 tax excl.
BDT 80.00 tax excl.
BDT 0.00 Tax
BDT 80.00 tax incl.
More
In-Stock
In stock: 4

Reference: RBD-1635

Dual Channel Motor Driver Shield For Arduino

(0)
Logic control, 5V from Arduino main board Polarity protection for External motor power input 2 fast test buttons for each motor channel Motor Driven Voltage:6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source) Up to 2A current each channel Pin 4, 5,6,7 are used to drive two DC motor Support PWM speed control Support  advance speed control
BDT 1,399.00
BDT 1,399.00 tax incl.
BDT 1,399.00 tax excl.
BDT 1,399.00 tax excl.
BDT 1,399.00 tax incl.
BDT 1,399.00 tax incl.
BDT 0.00 Tax
BDT 1,399.00 tax excl.
BDT 1,399.00 tax excl.
BDT 0.00 Tax
BDT 1,399.00 tax incl.
More
In-Stock
In stock: 5

Reference: RBD-0919

TP4056 Lithium Battery Charger Module With Protection Dual Functions

(0)
Dimension: 25 x 19 x 10 (LxWxH)mm. Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
BDT 38.00
BDT 38.00 tax incl.
BDT 38.00 tax excl.
BDT 38.00 tax excl.
BDT 38.00 tax incl.
BDT 38.00 tax incl.
BDT 0.00 Tax
BDT 38.00 tax excl.
BDT 38.00 tax excl.
BDT 0.00 Tax
BDT 38.00 tax incl.
More
In-Stock
In stock: 838

Reference: RBD-2696

HC-SR04 Ultrasonic Sensor Housing

(0)
Custom 3D-printed enclosure designed specifically for the HC-SR04 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. For convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates. 
BDT 85.00
BDT 85.00 tax incl.
BDT 85.00 tax excl.
BDT 85.00 tax excl.
BDT 85.00 tax incl.
BDT 85.00 tax incl.
BDT 0.00 Tax
BDT 85.00 tax excl.
BDT 85.00 tax excl.
BDT 0.00 Tax
BDT 85.00 tax incl.
More
Last items in stock
In stock: 3

Reference: RBD-1724

DC-5V-35V 5A PWM Motor Speed Controller

(0)
Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.
BDT 220.00
BDT 220.00 tax incl.
BDT 220.00 tax excl.
BDT 220.00 tax excl.
BDT 220.00 tax incl.
BDT 220.00 tax incl.
BDT 0.00 Tax
BDT 220.00 tax excl.
BDT 220.00 tax excl.
BDT 0.00 Tax
BDT 220.00 tax incl.
More
In-Stock
In stock: 74

Reference: RBD-0318

SIM900A Mini Module 5V

(0)
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock.  Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
BDT 1,050.00
BDT 1,050.00 tax incl.
BDT 1,050.00 tax excl.
BDT 1,050.00 tax excl.
BDT 1,050.00 tax incl.
BDT 1,050.00 tax incl.
BDT 0.00 Tax
BDT 1,050.00 tax excl.
BDT 1,050.00 tax excl.
BDT 0.00 Tax
BDT 1,050.00 tax incl.
More
In-Stock
In stock: 9

Reference: RBD-0215

IMAX B6-AC Charger/Discharger 1-6 Cells Dual Power 80W

(0)
AC 100~240v or 12V DC input The cables come with a fitted fuse. Microprocessor controlled Li-ion, LiPo, and LiFe capable Input voltage monitoring. (Protects car batteries at the field) Battery break-in and cycling feature Data storage (Store up to 5 packs in memory) Internal resistance checker to see pack health Delta-peak sensitivity Individual cell...
BDT 4,485.00
BDT 4,485.00 tax incl.
BDT 4,485.00 tax excl.
BDT 4,485.00 tax excl.
BDT 4,485.00 tax incl.
BDT 4,485.00 tax incl.
BDT 0.00 Tax
BDT 4,485.00 tax excl.
BDT 4,485.00 tax excl.
BDT 0.00 Tax
BDT 4,485.00 tax incl.
More
In-Stock
In stock: 9

Follow us on Facebook