Reference: RBD-1949
Banner

The Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A) is essentially a ramped up version of Ardumoto motor driver shield. For this Monster Moto Shield, It is replaced the L298 H-bridge with a pair of VNH3ASP30 full-bridge motor drivers. RoboticsBD
It is also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! The VIN and motor out are pitched for our 5mm screw terminals (not included), making it easy to connect larger gauge wires.
The L298 H-bridge is no longer available in the Motor Driver Shield Monster Moto since it has been replaced for a pair of VNH2SP30 full-bridge motor drivers. The Motor Driver Shield Monster Moto has been enhanced to drive a pair of high-current motors while the VIN and motor have been adjusted for connecting larger wires more easily. RoboticsBD
VNH3ASP30 is a full bridge motor driver intended for a wide range of automotive applications. The device incorporates a dual monolithic high side driver and two low side switches.
The high side driver switch is designed using the STMicroelectronics well known and proven proprietary VIPower M0 technology which permits efficient integration on the same die of a true Power MOSFET with an intelligent signal/protection circuitry. The VIN and motor out are pitched for 5mm screw terminals, making it easy to connect larger gauge wires. INA and INB control the direction of each motor, and the PWM pins turn the motors on or off.
For the VNH3ASP30, the current sense (CS) pins will output approximately 0.13 volts per amp of output current. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Driver Model | VNH3ASP30 |
| Operating Voltage (VDC) | 12 ~ 16 |
| Peak Current (A) | 14 |
| Continuous Current (A) | 30 |
| No. of Channels | 2 |
| Battery Protection Mode | Yes |
| Over-Current Protection (A) | Yes |
| Thermal Protection | Yes |
| Maximum PWM frequency | 20 kHz |
| LED Indicator | Yes |
| Cooling Fan | No |
| Arduino Sheild | Yes |
| Dimensions in mm (LxWxH) | 60 x 54 x 12 |
| Weight (gm) | 19 |
| Shipment Weight | 0.022 kg |
| Shipment Dimensions | 5 × 4 × 1 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Specific References
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: RBD-1949
Reference: RBD-1880
Reference: RBD-0259
Reference: RBD-0703
Reference: RBD-2614
Reference: RBD-0653
Reference: RBD-0699
Reference: RBD-1331
We'll slide into your inbox when the product is back in stock.
Reference: RBD-2541
Brand: DFRobot
Reference: RBD-0343
Reference: RBD-1653
Reference: RBD-2459
Reference: RBD-2043
Reference: RBD-4026
Reference: RBD-3205
Reference: RBD-3795
Reference: RBD-0009
Reference: RBD-0389
Reference: RBD-0557
Reference: RBD-0289
Reference: RBD-0392
Reference: RBD-0267
We'll slide into your inbox when the product is back in stock.
Reference: RBD-0376
Reference: RBD-0015
check_circle
check_circle