Reference: RBD-2065
Banner

The PCM5122 is a high-performance I2S digital-to-analog converter designed for converting digital audio from microcontrollers or single-board computers into high-quality stereo analog output. It supports simple hardware-only operation as well as advanced configuration via I2C or SPI, making it suitable for a wide range of audio projects.
The PCM5122 is a high-performance I2S digital-to-analog converter designed for converting digital audio from microcontrollers or single-board computers into high-quality stereo analog output. It supports simple hardware-only operation as well as advanced configuration via I2C or SPI, making it suitable for a wide range of audio projects.
High-quality stereo I2S DAC
Hardware mode works without configuration
Optional I2C or SPI control for advanced features
Line-level audio output via 3.5mm jack and breakout pads
No external MCLK required
Wide audio format and sample rate support
DAC Chip: PCM5122
Audio Channels: Stereo
Audio Interface: I2S
Supported Audio Formats:
I2S
Left-Justified
Right-Justified
TDM / DSP
Audio Bit Depth: 16-bit, 20-bit, 24-bit, 32-bit
Sampling Rate: Up to 384 kHz
Signal-to-Noise Ratio / Dynamic Range: 112 dB
THD+N: -93 dB (at -1 dBFS)
Power Supply Voltage: 3V to 5V
Digital Logic Level: 3.3V
Control Interfaces:
Hardware pin configuration
I2C
SPI
Output Type: Line-level analog audio
Minimum Load Impedance: 1 kΩ
Output Coupling: DC-coupled (centered on ground)
Dimensions: 37.6 x 22.8 x 6.4 mm
Country of Origin: Made in China
Digital audio projects with ESP32, RP2040, or similar MCUs
Raspberry Pi audio output
DIY audio players and streamers
Embedded audio systems
Line-level audio signal generation
Educational audio and signal processing projects
Supply the board with 3V to 5V power
Connect I2S signals: BCLK, WSEL (LRCK), and DIN
Use hardware mode for immediate operation, or configure via I2C/SPI for advanced control
Connect line-level output via the 3.5mm jack or analog output pads
1 x PCM5122 I2S stereo DAC breakout board
Pin header (not soldered)
This is a line-level output DAC and cannot drive headphones directly
Requires a load of 1 kΩ or higher
QT cable not applicable
Ensure correct I2S signal timing and logic levels
The PCM5122 I2S DAC breakout provides a flexible and high-quality solution for digital audio conversion. With excellent audio performance and multiple configuration options, it is well suited for both quick prototyping and advanced audio system design.
Specific References
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: RBD-2065
Reference: RBD-2085
Reference: RBD-3444
Reference: RBD-3810
Brand: DFRobot
Reference: RBD-2919
Reference: RBD-3665
Brand: DFRobot
Reference: RBD-2206
Reference: RBD-2318
Reference: RBD-3459
Reference: RBD-3777
Reference: RBD-2725
Reference: RBD-2496
Brand: DFRobot
Reference: RBD-1324
Reference: RBD-3328
Reference: RBD-1856
Reference: RBD-1772
Brand: Hi-Link
Reference: RBD-550
Reference: RBD-0690
Reference: RBD-0981
Reference: RBD-0990
Reference: RBD-1021
Reference: RBD-1324
Reference: RBD-1582
Reference: RBD-1772
Brand: Hi-Link
The PCM5122 is a high-performance I2S digital-to-analog converter designed for converting digital audio from microcontrollers or single-board computers into high-quality stereo analog output. It supports simple hardware-only operation as well as advanced configuration via I2C or SPI, making it suitable for a wide range of audio projects.
check_circle
check_circle