Reference: RBD-4165
SIM800L GSM/GPRS Cellular Communication Module (Micro-SIM, UART TTL)
Subscribe To When In Stock
We'll slide into your inbox when the product is back in stock.
Banner

The W5500 Ethernet co-processor breakout board provides reliable wired Ethernet connectivity for microcontroller and IoT projects. It communicates over SPI and includes the necessary support circuitry for use with 3.3V or 5V logic systems, making it suitable for stable network communication without wireless configuration.
The W5500 Ethernet co-processor breakout board provides reliable wired Ethernet connectivity for microcontroller and IoT projects. It communicates over SPI and includes the necessary support circuitry for use with 3.3V or 5V logic systems, making it suitable for stable network communication without wireless configuration.
Wired Ethernet connectivity using W5500 controller
SPI communication with dedicated chip select pin
Integrated RJ45 Ethernet connector
Link and activity status LEDs on Ethernet port
Onboard level shifting for 3.3V and 5V systems
Compatible with common Arduino and CircuitPython libraries
Ethernet Controller IC: W5500
Network Interface: 10/100 Mbps Ethernet
Communication Interface: SPI
Power Supply Voltage: 3.3V or 5V compatible
Logic Level Support: 3.3V and 5V
Ethernet Connector: RJ45 with integrated status LEDs
PoE Support: Not supported directly
Additional Requirements: External PoE splitter required if PoE is needed
PCB Status: Fully assembled and tested
Country of Origin: Made in China
IoT devices requiring stable wired networking
Industrial control systems
Network-enabled microcontroller projects
Data logging systems
Embedded Ethernet applications
Educational networking projects
Solder the included pin headers to the breakout board
Connect SPI pins and chip select to the microcontroller
Connect power and ground according to system voltage
Plug in a standard Ethernet cable
Use compatible Arduino or CircuitPython Ethernet libraries to configure networking
1 x W5500 Ethernet co-processor breakout board
1 x Pin header set (not soldered)
PoE is not supported directly on the board
Requires an SPI-capable microcontroller
Ethernet cable not included
Ensure correct SPI pin mapping before powering the board
The W5500 Ethernet co-processor breakout board offers a dependable wired networking solution for embedded systems. With SPI communication, onboard level shifting, and a standard RJ45 connector, it is well suited for projects that require consistent and robust Ethernet connectivity.
Specific References
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: RBD-4165
We'll slide into your inbox when the product is back in stock.
Reference: RBD-2720
Reference: RBD-3742
Brand: Waveshare
Reference: RBD-3174
Reference: RBD-3743
Brand: Waveshare
Reference: RBD-3463
Reference: RBD-0841
We'll slide into your inbox when the product is back in stock.
Reference: RBD-4021
Reference: RBD-2489
Reference: RBD-2488
Reference: RBD-3280
Reference: RBD-1134
Reference: RBD-3766
Reference: RBD-3744
Reference: RBD-2396
Reference: RBD-2064
We'll slide into your inbox when the product is back in stock.
Reference: RBD-0438
Reference: RBD-0797
Reference: RBD-0841
We'll slide into your inbox when the product is back in stock.
Reference: RBD-1134
Reference: RBD-1137
Reference: RBD-1557
Reference: RBD-1722
Reference: RBD-2064
We'll slide into your inbox when the product is back in stock.
The W5500 Ethernet co-processor breakout board provides reliable wired Ethernet connectivity for microcontroller and IoT projects. It communicates over SPI and includes the necessary support circuitry for use with 3.3V or 5V logic systems, making it suitable for stable network communication without wireless configuration.
check_circle
check_circle