Analog 0-12V 4-20mA Signal Generator for PLC and Panel Debugging & Device Testing is designed to simulate 0-12V voltage signal and 0-24mA current signal for PLC and panel Debugging, Device Testing, Frequency Converter, Flow Valve, etc. Very easy to use, it can be connected with micro USB 5V power supply. What’s more, it can display 4 different types of digits, 0-12V voltage, 0-24mA current, 0-100 percent, and 0-50HZ. It plays an important role in your electronics work. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
Voltage Output: 0-12V, precision is 0.01V, rotate the encoder knob to adjust the output voltage, can be calibrated.
Current Output: 0-22mA, precision is 0.01mA, rotate the encoder knob to adjust output current, can be calibrated. RoboticsBD
Multiple Display: just push the small button to switch the display mode between voltage and current, you can also follow the instructions to switch 0-100 percent or 0-50HZ display.
Parameter Settings:（Rotate one grid clockwise is "+" Rotate one grid counter-clockwise is "-", Press the knob. is "Confirm"）
Press and hold the knob for 2 seconds to enter the parameter setting, Display parameter number "F001", Then press "Confirm ", to Set the value of parameter "F001", =0 is coarse tuning; =1 Fine tuning; Then press "Confirm" to save its value.
When the parameter number "FXXX" is displayed, "+" "-" Rotation modification parameter number; Enter the password first "+ - - +", To enter the F002 parameter; Enter the password first "+ - + -", To enter the F100 parameter; Enter the password first "- + - +", To enter the F200 parameter.
Package Includes:
1 x 4-20mA Signal Generator Current Loop Simulator Tester.
Dual-function meter: Simultaneous measurement of DC voltage (0–100V) and current (0–100A). Clear dual LED display: Red for voltage and blue for current for quick, easy reading. High accuracy: 1% measurement precision with 0.1V and 0.01A resolution. Built-in shunt: Supports direct connection for accurate current monitoring. Wide application: Perfect for...
The INA237 is a high-precision DC current, voltage, and power monitoring module designed for high-side measurement applications. It uses a 16-bit delta-sigma ADC to provide accurate electrical measurements and supports energy and charge accumulation. With an I2C interface and STEMMA QT / Qwiic connectivity, it is suitable for power monitoring in embedded,...
Bi-directional Hall-effect current sensor with a ±50A detection range. Accurate and stable current measurement with a 40mV/A linearity. Compact design with easy mounting capability for versatile applications. Wide operating temperature range: -40°C to 150°C, suitable for harsh environments. Based on ACS758LCB-050B IC, offering high reliability and low...
INA3221 Triple-Channel Shunt Current and Voltage Monitor Sensor Board Measures high-side current and bus voltage with I2C and SMBUS compatibility Monitors bus voltages (0V to 26V) and shunt voltage drops with high accuracy Programmable alerts, averaging modes, and conversion times for enhanced control Compact design with four programmable I2C addresses...
High-precision voltage, current, and power monitoring module using INA226 sensor. 16-bit ADC resolution ensures accurate and stable real-time measurements. Supports I²C communication with Arduino, Raspberry Pi, ESP32, and STM32. Measures both high-side and low-side currents for flexible circuit integration. Wide input voltage range up to 36V with...
KA75330 3.3V voltage detector for reset/enable control Prevents microcontrollers from running at dangerously low voltages Monitors supply voltage and pulls output low below 3.3V Starts operating from as low as 0.8V, ensuring early protection Ideal for Li-Po battery-powered projects and ESP8266/Feather boards Compact, reliable solution for power startup...
INA219 DC current and voltage measurement module with I2C interface Measures high-side current up to 3.2A with 0.8mA resolution Supports load voltages from 0–26VDC Powered by 3–5V, compatible with both 3.3V and 5V logic MCUs Integrated 0.1Ω shunt resistor ensures accurate measurements Adjustable I2C address for multiple modules on the same bus
VL53L1X advanced Time-of-Flight (ToF) laser sensor for precise distance measurement Measures up to 4 meters with 50 Hz ranging frequency 940 nm Class 1 invisible laser with SPAD array and IR filters Works reliably under different lighting conditions and target surfaces Programmable ROI allows adjustable field-of-view and multizone detection Compact,...
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm
Measures voltage, current, power, and energy with 1.0 accuracy rating Supports AC measurement range 80–260V and up to 100A load capacity TTL serial communication interface for easy data reading and parameter setup Compatible with Arduino, ESP32, and Raspberry Pi for energy monitoring projects Includes Open CT sensor for safe, non-invasive current...
We'll slide into your inbox when the product is back in stock.
You have successfully subscribed to this product
The INA219 is a digital current, voltage, and power monitoring module based on the TI INA219 chip. It uses an I2C interface to measure DC current and bus voltage while calculating power in real time. This module is suitable for power management, battery monitoring, and smart hardware projects, with easy plug-and-play connectivity via STEMMA QT / Qwiic.
WCS1700 Hall Current Sensor Module for AC and DC current measurement Wide detection range from 0A to 70A Linear analog output with 33mV/A sensitivity High isolation voltage up to 4000V RMS Operates with 3V–5V supply (5V recommended) Ideal for power monitoring, motor control, and battery systems
Power Supply: external micro USB-5V. Voltage Output: 0-10V. Current Output: 0-20mA. Multiple Display: just push the small button to switch the display mode
We'll slide into your inbox when the product is back in stock.
You have successfully subscribed to this product
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Wide Supply Range: 2.0v To 5.5vLow Current ConsumptionContinuous Mode: Only 150µa Single-shotAuto Shut-downProgrammable Data Rate: 8SPS to 860SPSIt has Internal low-drift voltage reference
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 20A Sensitivity: 100mV/A
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A
Low-noise analog signal path. Device bandwidth is set via the new FILTER pin. 5 µs output rise time in response to step input current. Small footprint, low-profile SOIC8 package. 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
