- Pack
Banner

This TP4056 1A Li-Ion Battery Charging Board Micro USB with Current Protection is a tiny module, perfect for charging single cell 3.7V 1 Ah or higher lithium-ion (Li-Ion) cells such as 16550s that don’t have their own protection circuit. Based on the TP4056 charger IC and DW01 battery protection IC this module will offer 1A charge current then cut off when finished.
Furthermore, when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1. Ampere meter can only be connected to a 5v input end of the module.
2. It is better than the charging current is 37% of the battery capacity. If you charge the battery of 1000mAh, a current of 400mAh is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-subtract the charging current to avoid burn damage to the chip.
6. NO Reverse polarity.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Charging accuracy (%) | 1.5 |
| Charging method | Linear |
| Full Charge Voltage (V) | 4.2 |
| Over-Current Protection (A) | 3 |
| Under-Voltage Protection (V) | 2.5 |
| Input Voltage (V) | 4.5-5.5 |
| Rated Power (W) | 4.2 |
| Operating Temperature (°C) | -10 to 85 |
| Length (mm) | 25 |
| Width (mm) | 20 |
| Height (mm) | 6 |
| Weight (gm) | 3 |
| Shipment Weight | 0.007 kg |
| Shipment Dimensions | 12 × 8 × 2.5 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x 14500 Lithium Battery Charger
Specific References
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: RBD-4028
Reference: RBD-0368
Reference: RBD-2513
Reference: RBD-1706
We'll slide into your inbox when the product is back in stock.
Reference: RBD-0233
Brand: SparkFun Electronics
We'll slide into your inbox when the product is back in stock.
Reference: RBD-0326
Reference: RBD-0122
Reference: RBD-0396
Reference: RBD-2058
Reference: RBD-2261
Reference: RBD-0742
Reference: RBD-0715
Reference: RBD-2383
Reference: RBD-2007
Reference: RBD-3636
Brand: DFRobot
Reference: RBD-2524
Reference: RBD-0836
Reference: RBD-0376
Reference: RBD-1754
Reference: RBD-0022
Reference: RBD-2640
Reference: RBD-0020
Reference: RBD-0837
Reference: RBD-1714
Reference: RBD-0836
Reference: RBD-0989
Reference: RBD-0837
Reference: RBD-1822
Reference: RBD-1334
We'll slide into your inbox when the product is back in stock.
check_circle
check_circle