Reference: RBD-1336
Banner

Note: Relay brand may vary from actual product as our stock rotates.
This is a single channel relay board with one 24 volts high current relay. It is an ideal board to control & switch high current loads like a fan, lights, low power heater coils. It not only provides switching but also provides isolation between the power device and your micro-controller. Devices up to 5 Ampere can be switched using this relay.
This relay module has an onboard driver and a led to indicate the Relay Status (ON/OFF). Since this Relay board has an onboard driver transistor to provide the relay with the necessary holding and latching current these relays can work with any microcontroller, Arduino, Intel Edison Boards, Beagle-bone & Raspberry pi as well.. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
Note: Relay brand may vary from actual product as our stock rotates.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Maximum Load | AC 250V/10A, DC 30V/10A |
| Isolation | SMD Optocoupler, trigger current of only 5mA |
| Relay Power Supply | 5V, 9V, 12V, and 24V available |
| Trigger Select | High or low, set via jumper |
| Fault-Tolerant Design | Relay will maintain even if control line is broken |
| Indicators | Power (green) and relay status (red) |
| Size | 50mm x 26mm x 18.5mm |
| Mounting Holes | Four holes, 3.1mm in diameter, with a pitch of 44.5mm x 20.5mm |
| Input VCC | Relay power supply positive |
| Input GND | Relay power supply negative |
| Input IN | Signal trigger input for high or low level signal, select via jumper |
| Output NO | Relay normally open |
| Output COM | Relay common pin |
| Output NC | Relay normally closed |
| High Level Trigger | IN input high level signal, NO connects with COM; IN input low level signal, NC connects with COM |
| Low Level Trigger | IN input low level signal, NO connects with COM; IN input high level signal, NC connects with COM |
| Shipment Weight | 0.03 kg |
| Shipment Dimensions | 12cm x 8cm x 4cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x 1 Channel 24V Relay Board Module with OPTO Isolation Support High or Low Level Trigger
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Specific References
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: RBD-1336
Reference: RBD-2421
Reference: RBD-0159
Reference: RBD-2559
Reference: RBD-1753
Reference: RBD-3444
Reference: RBD-1180
Reference: RBD-2923
Reference: RBD-3324
Reference: RBD-0742
Reference: RBD-0306
Reference: RBD-0353
Reference: RBD-0392
Reference: RBD-2149
Reference: RBD-2120
Reference: RBD-2460
Reference: RBD-0948
Reference: RBD-0133
Reference: RBD-1174
Reference: RBD-2640
Reference: RBD-2641
Reference: RBD-3260
Reference: RBD-0132
Reference: RBD-0217
We'll slide into your inbox when the product is back in stock.
Reference: RBD-2226
Reference: RBD-1920
Reference: RBD-2204
Reference: RBD-2205
We'll slide into your inbox when the product is back in stock.
Note: Relay brand may vary from actual product as our stock rotates.
check_circle
check_circle