Reference: RBD-0337
Brand: Waveshare
Banner

This is 2Amp Motor Driver Shield newly revised dual channel 2A motor shield. It uses L298P chip which allows control of two 5 – 26V DC brush motors with the maximum of 2A current each channel. This shield can be directly stacked onto standard Arduino UNO, Duemilanove, Leonardo, Mega and also CIKU (PIC18F4550). RoboticsBD
Motor power polarity protection, also fast test or manual control buttons for each channel of the motor. Adding LSS05 (Auto-calibration line sensor) to Arduino will be easy as this shield comes with the socket for it. RoboticsBD
The speed control is achieved through conventional PWM which can be obtained from Arduino‘s PWM output pin 5 and 6. The enable/disable of motor driver is controlled by Arduino pin 4 and 7, this is labeled as Signed magnitude control. You have the option to configure it to become Locked Anti-phase which uses PWM signal to decide direction, speed and also start/stop of the motor. The control modes can be configured from jumpers and also program.
The Motor shield can be powered directly from Arduino or from the external power source (jumper to select). It is strongly encouraged to use the external power supply to power the motor shield. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
This module is compatible with following Arduino versions, click on their name below to buy them
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Motor Channel | 2 |
| Operating Voltage (VDC) | 6.5 ~ 12 |
| Peak Current (A) | 2 |
| Continuous Current (A) | 0.8 |
| Length (mm) | 69 |
| Width (mm) | 57 |
| Height (mm) | 24 |
| Weight (gm) | 30 |
| Shipment Weight | 0.033 kg |
| Shipment Dimensions | 8 × 7 × 4 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Dual Channel Motor Driver Shield For Arduino.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Specific References
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: RBD-0337
Brand: Waveshare
Reference: RBD-1603
Reference: RBD-3053
Reference: RBD-3682
Reference: RBD-1808
Reference: RBD-0703
Reference: RBD-2087
Reference: RBD-2097
Reference: RBD-2542
Brand: DFRobot
We'll slide into your inbox when the product is back in stock.
Reference: RBD-1910
Reference: RBD-1408
Reference: RBD-1337
Reference: RBD-3517
Reference: RBD-2089
Reference: RBD-1815
Reference: RBD-2920
Reference: RBD-1626
Brand: RoboticsBD
Reference: RBD-1849
Reference: RBD-2104
Reference: RBD-2105
Reference: RBD-2106
Reference: RBD-2754
Reference: RBD-3085
We'll slide into your inbox when the product is back in stock.
Reference: RBD-0323
Reference: RBD-0154
Reference: RBD-0009
Reference: RBD-0094
Reference: RBD-1875
Reference: RBD-0376
Reference: RBD-0377
Reference: RBD-0684
Reference: RBD-0922
check_circle
check_circle