Reference: RBD-2131
Banner

A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and instead use the recommended cable available here: High-Quality USB Cable.
The core of this module is the ESP32 chip, which is scalable and adaptive. Two CPU cores can be individually controlled. The clock frequency is adjustable from 80 MHz to 240 MHz and supports RTOS. RoboticsBD
It is a general-purpose Wi-Fi+BT+BLE MCU module.ESP-WROOM-32s The module integrates traditional Bluetooth, Bluetooth low energy and Wi-Fi. Wide range of uses: Wi-Fi supports a wide range of communication connections, as well as a direct connection to the Internet via a router; Bluetooth allows users to connect to a mobile phone or broadcast a BLE Beacon for signal detection. RoboticsBD
The module supports data rates up to 150 Mbps and antenna output power of 20dBm for maximum wireless communication. As a result, this module has industry-leading specifications and performs well in terms of high integration, wireless transmission distance, power consumption, and network connectivity Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Module model | ESP-WROOM-32 Type C |
| SPI Flash | 32Mbit(default) |
| Support interface | UART/GPIO/ADC/DAC/SDIO/SD card /PWM/I2C/I2S |
| Integrated crystal oscillator | 40MHz Crystal oscillator |
| IO Port | 38 |
| Antenna | Onboard antenna |
| Power Supply | Voltage 3.0V ~ 3.6V,Typical 3.3V,Current >500mA |
| Operating Temperature | -40 ℃ ~ 85 ℃ |
| Storage Environment | -40 ℃ ~ 120 ℃ |
| Length(mm) | 25.4 |
| Width(mm) | 48.26 |
| Height(mm) | 3 |
| Weight(g) | 10 |
| Shipment Weight | 0.015 kg |
| Shipment Dimensions | 12 × 8 × 2 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x ESP32 ESP-32S 30P NodeMCU Development Board Wireless WiFi
Specific References
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: RBD-2131
Reference: RBD-0682
Reference: RBD-2344
Reference: RBD-3681
Reference: RBD-3720
Brand: ST Microelectronics
Reference: RBD-1812
Reference: RBD-3008
Reference: RBD-1806
Reference: RBD-3421
Reference: RBD-3003
Reference: RBD-0154
Reference: RBD-1131
Reference: RBD-3732
Brand: Arduino Official
Reference: RBD-3597
Reference: RBD-3422
Reference: RBD-2417
Reference: RBD-0133
Reference: RBD-2639
Reference: RBD-2640
Reference: RBD-0768
Reference: RBD-1354
Reference: RBD-2641
Reference: RBD-0120
Reference: RBD-0376
Reference: RBD-1671
Reference: RBD-0948
Reference: RBD-1407
Reference: RBD-0694
Reference: RBD-1810
Reference: RBD-1765
Reference: RBD-1806
Reference: RBD-1402
Reference: RBD-1255
Reference: RBD-1558
Reference: RBD-1412
A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and instead use the recommended cable available here: High-Quality USB Cable.
check_circle
check_circle