Reference: RBD-3130
Banner

This Pro Micro 5V 16M Mini Leonardo Microcontroller Development Board For Arduino development board has 4 channel 10 bit ADC, 5 PWM pins, 12 DIO, and a hardware serial connection Rx and Tx you are familiar with Running on 16MHz and 5V, this board will remind you a lot of other Arduino compatible boards that you like.
There is a voltage regulator on board, so it can accept up to 12V DC. RoboticsBD
The Micro is a microcontroller board based on the ATmega32U4. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. RoboticsBD
It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.
The Micro board is similar to the Arduino Leonardo in that the ATmega32U4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Micro to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port.
If you supply an unstable power supply board, be sure to connect to the “RAW”, not on the VCC pin. It has also added a PTC fuse and diode protection to the power circuit and to correct the RX and LED TX circuits. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Microcontroller | ATmega32U4 |
| Input Voltage(Recommended) | 7-12V |
| Operating Voltage (VDC) | 5 |
| Input Voltage (limits) | 6-20V |
| Analog I/O Pins | 12 |
| Digital I/O Pins | 20 |
| DC Current per I/O Pin (mA) | 20 |
| DC Current for 3.3V Pin (mA) | 50 |
| PWM Pins | 7 |
| Flash Memory | 32 KB |
| EEPROM | 2.5KB |
| SRAM | 1 |
| Clock Speed | 16 MHz |
| Dimensions (mm) LxWxH | 48x18x8 |
| Weight (gm) | 13 |
| Shipment Weight | 0.06 kg |
| Shipment Dimensions | 8 × 6 × 4 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Arduino Pro Micro 5V/16MHz
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Specific References
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: RBD-3130
Reference: RBD-0323
Reference: RBD-3687
Reference: RBD-2551
Reference: RBD-3843
Reference: RBD-1806
Reference: RBD-2651
Reference: RBD-1603
Reference: RBD-0009
Reference: RBD-1214
Reference: RBD-2568
Reference: RBD-2162
Reference: RBD-3676
Brand: Waveshare
Reference: RBD-3595
Reference: RBD-3723
Brand: ST Microelectronics
Reference: RBD-3834
Reference: RBD-0654
Reference: 0245
Reference: RBD-0761
Reference: 0828
Reference: RBD-0349
Reference: RBD-0389
Reference: RBD-0658
Reference: RBD-0833
Reference: RBD-0136
Reference: RBD-0009
Reference: RBD-0032
Reference: RBD-1523
Reference: RBD-0094
Reference: RBD-0133
Reference: RBD-1153
Reference: RBD-0549
check_circle
check_circle